Control settings |
The Sampler control parameters are in the following sections: Missing Vial Mark the Ignore missing vial check box to specify that, if a vial is missing, the injector ignores it and continues with a 6-second dummy run. The message "Missing vial <x>" is logged, and the system continues with the next injection. Illumination Toggles the illumination of the sample area, On or Off. At Power On The section is available when a thermostat is installed and configured. Mark the Turn on Thermostat check box to specify that the thermostat is switched on automatically when the instrument is switched on. Thermostat The section is available when a thermostat is installed and configured and the Constant temperature mode is selected. Select On to switch on the thermostat. Specify the required temperature in the adjacent field. The specified temperature must be at least 5 °C below ambient for proper temperature control. Select Off to switch off the thermostat. Automatic Turn On You can set a date and time at which the thermostat switches on automatically. Pump connected to Sampler Use this section to specify the pump that is used with the Sampler. If more than one pump is configured, display the drop-down list and select the appropriate pump from the list. Clear Workspace Immediately Returns the sample container on the workspace to its position in the sample hotel immediately after the injection has been completed. This allows you to quickly retrieve the sample container for further processing. At End of Analysis Returns the sample container on the workspace to its position in the sample hotel after the current run or sequence/worklist has been completed. This is the default setting. Never Leaves the sample container on the workspace until a different sample container is required to replace it. Enable Analysis This feature requires LC & CE Drivers A.02.19 or newer and is only available for the Sample Thermostat. With this function, you can specify if the analyses should start With any temperature or only when the Temperature is within ± 2 °C range of the setpoint temperature. NOTE: The Enable Analysis section is disabled when Not controlled is selected in the Temperature section.
|
Control settings | The Sampler control parameters are in the following sections: Missing Vial Mark the Ignore missing vial check box to specify that, if a vial is missing, the injector ignores it and continues with a 6-second dummy run. The message "Missing vial <x>" is logged, and the system continues with the next injection. Illumination Toggles the illumination of the sample area, On or Off. At Power On The section is available when a thermostat is installed and configured. Mark the Turn on Thermostat check box to specify that the thermostat is switched on automatically when the instrument is switched on. Thermostat The section is available when a thermostat is installed and configured and the Constant temperature mode is selected. Select On to switch on the thermostat. Specify the required temperature in the adjacent field. The specified temperature must be at least 5 °C below ambient for proper temperature control. Select Off to switch off the thermostat. Automatic Turn On You can set a date and time at which the thermostat switches on automatically. Pump connected to Sampler Use this section to specify the pump that is used with the Sampler. If more than one pump is configured, display the drop-down list and select the appropriate pump from the list. Enable Analysis This feature requires LC & CE Drivers A.02.19 or newer and is only available for the Sample Thermostat. With this function, you can specify if the analyses should start With any temperature or only when the Temperature is within ± 2 °C range of the setpoint temperature. NOTE: The Enable Analysis section is disabled when Not controlled is selected in the Temperature section.
|
Control settings | The Sampler control parameters are in the following sections: Missing Vial Mark the Ignore missing vial check box to specify that, if a vial is missing, the injector ignores it and continues with a 6-second dummy run. The message "Missing vial <x>" is logged, and the system continues with the next injection. Illumination Toggles the illumination of the sample area, On or Off. At Power On The section is available when a thermostat is installed and configured. Mark the Turn on Thermostat check box to specify that the thermostat is switched on automatically when the instrument is switched on. Thermostat The section is available when a thermostat is installed and configured and the Constant temperature mode is selected. Select On to switch on the thermostat. Specify the required temperature in the adjacent field. The specified temperature must be at least 5 °C below ambient for proper temperature control. Select Off to switch off the thermostat. Automatic Turn On You can set a date and time at which the thermostat switches on automatically. Pump connected to Sampler Use this section to specify the pump that is used with the Sampler. If more than one pump is configured, display the drop-down list and select the appropriate pump from the list. Clear Workspace Immediately Returns the sample container on the workspace to its position in the sample hotel immediately after the injection has been completed. This allows you to quickly retrieve the sample container for further processing. At End of Analysis Returns the sample container on the workspace to its position in the sample hotel after the current run or sequence/worklist has been completed. This is the default setting. Never Leaves the sample container on the workspace until a different sample container is required to replace it. Enable Analysis This feature requires LC & CE Drivers A.02.19 or newer and is only available for the Sample Thermostat. With this function, you can specify if the analyses should start With any temperature or only when the Temperature is within ± 2 °C range of the setpoint temperature. NOTE: The Enable Analysis section is disabled when Not controlled is selected in the Temperature section.
|