Specifications

Weight

21.0 kg (46.3 lbs)

Dimensions (height × width × depth)

200 x 396 x 436 mm (7.9 x 15.6 x 17.2 inches)

Line voltage

100–240 V~, ±10%

Wide-ranging capability

Line frequency

50 or 60 Hz, ±5%

Power consumption

210 VA / 180 W

Ambient operating temperature

4–55 °C (39–131 °F)

Ambient non-operating temperature

-40–70 °C (-40–158 °F)

Humidity

< 95% r.h. at 40 °C (104 °F)

Non-condensing

Operating altitude

Up to 3000 m (9842 ft)

Safety standards: IEC, EN, CSA, UL

Overvoltage category II, Pollution degree 2

For indoor use only

ISM Classification

ISM Group 1 Class B

According to CISPR 11

Hydraulic system

Two dual pistons in series pump with proprietary servo-controlled variable stroke design and smooth motion control for active damping.

Designed for use with Agilent InfinityLab Assist

Intuitive User Interface, Automated Workflows, Predictive Maintenance & Assisted Troubleshooting

Pump resolution step size

300 pL

Flow range

Settable: 0.001 – 5 mL/min, in 0.001 mL/min increments (executed in 300 pL/step increments)

Flow precision

≤ 0.07 % RSD or 0.005 min SD, whichever is greater

Based on retention time at constant temperature

Flow accuracy

± 1 % or ± 10 µL/min, whichever is greater

Pressure operating range

Up to 130 MPa (1300 bar) at 0 – 2 mL/min

ramping down to 80 MPa (800 bar) at 5 mL/min

Pressure pulsation

< 1 % amplitude or < 0.5 MPa (5 bar), whichever is greater

Compressibility compensation

Automatic

Recommended pH range

1.0 – 12.5 

Solvents with pH < 2.3  should not contain acids which attack stainless steel

Gradient formation

High-pressure binary mixing

Delay volume

As low as 45 µL (10 µL without mixer)

Composition range

0 – 100 %

Composition precision

< 0.15 % RSD or 0.01 min SD, whichever is greater

Composition accuracy

± 0.35 % absolute

Number of solvents

2 out of maximum 26 solvents

Solvent selection valve

Internal 4-solvent selection valve included.

External 2 x 12 solvent valve as option, fully integrated in the pump control interface.

Integrated degassing unit

Number of channels: 2

Internal volume per channel: 1.5 mL

Materials in contact with solvent

TFE/PDD copolymer, PFA, PEEK, FEP, ETFE, Stainless Steel, FFKM, Gold, Ruby, Zirconium Oxide-based ceramic, Tantalum, UHMW-PE, Polyimide, DLC Coated Stainless Steel

Automatic purge valve

Included

Active seal wash

Included

Intelligent System Emulation Technology (ISET)

Included

Instrument control

LC & CE Drivers A.02.11 or above

Instrument Control Framework (ICF) A.02.03 or above

Lab Advisor software B.02.06 or above

InfinityLab Assist (G7180A) with firmware D.07.40 or above

Instant Pilot (G4208A) with firmware B.02.17 or above

For details about supported software versions refer to the compatibility matrix of your version of the LC & CE Drivers

Communication

Controller Area Network (CAN), RS232C, APG remote: ready, start, stop, and shutdown signals, LAN

Safety features and maintenance

Leak detection, safe leak handling, leak output signal for shutdown of the pumping system.

Low voltage in major maintenance areas.

Extensive diagnostics, error detection and display with Agilent InfinityLab Assist and with Agilent Lab Advisor software.

GLP feature

Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of seal wear and volume of pumped mobile phase with pre-defined and user settable limits and feedback messages.

Electronic records of maintenance and errors.

Housing

All materials are recyclable