Specifications of the G7167B Multisampler

Weight

22 kg (48.5 lbs)

w/o sample thermostat, w/o sample ID reader

Dimensions (height × width × depth)

320 x 396 x 468 mm (12.6 x 15.6 x 18.4 inches)

Line voltage

100–240 V~, ±10%

Wide-ranging capability

Line frequency

50 or 60 Hz, ±5%

Power consumption

180 VA, 180 W

Ambient operating temperature

4–40 °C (39–104 °F)

Ambient non-operating temperature

-40–70 °C (-40–158 °F)

Humidity

< 95% r.h. at 40 °C (104 °F)^{SampleThermostatIncluded}

Non-condensing

Operating altitude

Up to 3000 m (9842 ft)

Safety standards: IEC, EN, CSA, UL

Overvoltage category II, Pollution degree 2

For indoor use only.

ISM Classification

ISM Group 1 Class B

According to CISPR 11

Permitted solvents

Boiling point ≥ 56 °C (133 °F) Auto-ignition temperature ≥ 200 °C (392 °F)

Designed for use with Agilent InfinityLab Assist

Intuitive User Interface, Automated Workflows, Predictive Maintenance & Assisted Troubleshooting

Injection range for Single-needle instruments

Default: 0.1 – 20 µL in 0.1 µL increments; optional: 40 µL or 100 µL (using optional 100 µL analytical head)

Up to 1300 bar using 40 µL (default) or optional 100 µL analytical head

0.1 – 500 µL or 900 µL in 0.1 µL increments (using 900 µL analytical head)

Pressure range up to 400 bar due to 900 µL analytical head

0.1 – 120 µL in 0.1 µL increments with 1290 Infinity II large volume injection kit (hardware modification required) G4216-68711

0.1 – 500 µL or 1500 µL in 0.1 µL increments with 100 µL upgrade kit (hardware modification required) G7167-68711

Pressure range up to 1300 bar Multi-draw mode (Injection into needle-seat capillary)

Injection range for Dual-needle instruments

Default: 0.1 – 20 µL in 0.1 µL increments; optional: 40 µL or 100 µL

Up to 1300 bar using 100 µL analytical head

Up to 500 µL in 0.1 µL increments depending on installed loop size

Up to 1300 bar using 100 µL analytical head + Multi-load

Injection precision for single-needle instruments

<0.15 % RSD or SD <10 nL, whatever is greater

Measured caffeine

Injection precision for dual-needle instruments

<0.2 % RSD or SD <10 nL, whatever is greater

Measured caffeine

Injection linearity

0.9999  in the range of 0.1 – 100 µL

Measured caffeine

Pressure range

Up to 1300 bar

Max pressure for basic instrument

Sample viscosity range

0.2 – 5.0 cP

Sample capacity

1H Drawer up to 8 drawers and 16 positions shallow well plates (MTP)

Max. 6144/1536 samples (384 MTP/96)

2H Drawer up to 4 drawers and 8 positions MTP, deep well plates, vials, Eppendorf

3072 samples, 432 vials (2 mL)

3H Drawer up to 2 drawers and 4 positions MTP, deep well plates, vials up to 6 mL, Eppendorf

1536 samples, 60 vials (6 mL), 384 vials (1 mL), 216 vials (2 mL)

Injection cycle time

<10 s using following standard conditions:

Default draw speed: 100 µL/min

Default eject speed: 400 µL/min

Injection volume: 1 µL

Time between 2 injections is not mechanically limited, time delay depends on communication speed of software, OS or network connections

Carryover

<0.003 % (30 ppm) Multisampler Standard and Dual Needle

<0.0009 % (9 ppm) Multisampler Multiwash

Sample: Chlorhexidine

Multiwash

Outer needle wash and seat backflush for carryover reduction with up to 3 different solvents

Instrument Control

LC & CE Drivers A.02.10 or above

Instrument Control Framework (ICF) A.02.03 or above

InfinityLab Assist (G7180A) with firmware D.07.40 or above

Instant Pilot (G4208A) with firmware B.02.19 or above

Lab Advisor B.02.06 or above

For details about supported software versions refer to the compatibility matrix of your version of the LC & CE Drivers

Communication

Controller Area Network (CAN),

Local Area Network (LAN),

ERI: ready, start, stop and shut-down signals

Maintenance and safety-related features

Extensive diagnostics, error detection and display with Agilent InfinityLab Assist and with Agilent Lab Advisor software

Leak detection, safe leak handling, leak output signal for shutdown of pumping system, and low voltages in major maintenance areas

GLP features

Early maintenance feedback (EMF) for continuous tracking of instrument usage with user-settable limits and feedback messages. Electronic records of maintenance and errors.

Housing

All materials recyclable.