Specifications of the G7137A Bio Multisampler

Weight

22 kg (48.5 lbs)

w/o sample thermostat, w/o sample ID reader

Dimensions (height × width × depth)

320 x 396 x 468 mm (12.6 x 15.6 x 18.4 inches)

Line voltage

100–240 V~, ±10%

Wide-ranging capability

Line frequency

50 or 60 Hz, ±5%

Power consumption

180 VA, 180 W

Ambient operating temperature

4–40 °C (39–104 °F)

Ambient non-operating temperature

-40–70 °C (-40–158 °F)

Humidity

< 95% r.h. at 40 °C (104 °F)^{SampleThermostatIncluded}

Non-condensing

Operating altitude

Up to 3000 m (9842 ft)

Safety standards: IEC, EN, CSA, UL

Overvoltage category II, Pollution degree 2

For indoor use only.

ISM Classification

ISM Group 1 Class B

According to CISPR 11

Permitted solvents

Boiling point ≥ 56 °C (133 °F) Auto-ignition temperature ≥ 200 °C (392 °F)

Designed for use with Agilent InfinityLab Assist

Intuitive User Interface, Automated Workflows, Predictive Maintenance & Assisted Troubleshooting

Injection range

Default 0.1 – 20 µL in 0.1 μL increments

optional: 40 μL or 100 μL (using optional 100 μL analytical head)

Up to 1300 bar using the 40 μL (default) or optional 100 μL analytical head

0.1 – 500 µL or 1500 μL in 0.1 µL increments with 100 μL upgrade kit (hardware modification required G7137-68711)

Pressure range up to 1300 bar Multidraw mode (injection into needle-seat capillary)

Injection precision

< 0.15 % RSD or SD < 10 nL, whatever is greater

Measured caffeine

Injection linearity

> 0.9999 

Measured caffeine

Pressure range

Up to 1300 bar

Max pressure for basic instrument.

Sample viscosity range

0.2 – 5.0 cP

Sample capacity

1H Drawer up to 8 drawers and 16 positions shallow well plates (MTP)

Max. 6144 /1536  samples (384  MTP/96)

2H Drawer up to 4 drawers and 8 positions MTP, deep well plates, vials, Eppendorf

3072  samples, 432  vials (2 mL)

3H Drawer up to 2 drawers and 4 positions MTP, deep well plates, vials up to 6 mL, Eppendorf

1536  samples, 60  vials (6 mL), 384  vials (1 mL), 216  vials (2 mL)

Injection cycle time

< 10 s using following standard conditions:

Default draw speed: 100 μL/min

Default eject speed: 400 µL/min

Injection volume: 1 μL

Time between 2 injections is not mechanically limited, time delay depends on communication speed of software, OS or network connections

pH Range

pH 1 – 12.5 , short term pH 13 (for flushing)

Carryover

< 0.003 % (30 ppm) Multisampler Standard

< 0.0009 % (9 ppm) Multisampler Multiwash

Sample: Chlorhexidine

Multiwash

Outer needle wash and seat backflush for carryover reduction with up to 3 different solvents

Materials in the flow path

MP35N, Gold, PEEK, UHMW-PE

Instrument control

LC & CE Drivers Rev. 3.3 or above

Instrument Control Framework (ICF) A.02.03 or above, available in emulation mode

Instrument Control Framework (ICF) ICF 3.0 Update 1 or above

LC Instrument Firmware Rev. D.07.33 or above

InfinityLab Assist (G7180A) with firmware D.07.40 or above

Instant Pilot (G4208A) with firmware B.02.24 or above

Lab Advisor B.02.16 or above

For details about supported software versions refer to the compatibility matrix of your version of the LC & CE Drivers

Communication

Controller Area Network (CAN), Local Area Network (LAN), ERI: ready, start, stop and shut-down signals

Maintenance and safety-related features

Extensive diagnostics, error detection and display with Agilent InfinityLab Assist and with Agilent Lab Advisor software.

Leak detection, safe leak handling, leak output signal for shutdown of pumping system, and low voltages in major maintenance areas.

GLP features

Early maintenance feedback (EMF) for continuous tracking of instrument usage with user-settable limits and feedback messages. Electronic records of maintenance and errors.

Housing

All materials recyclable