Specifications

Weight

12.5 kg (27.6 lbs)

Dimensions (height × width × depth)

160 x 435 x 436 mm (6.3 x 17.1 x 17.2 inches), Width with column identification kit: 460 mm

G7116A only has a Column ID tag reader on the left hand side.

Line voltage

100–240 V~, ±10%

Wide-ranging capability

Line frequency

50 or 60 Hz, ±5%

Power consumption

150 VA, 150 W

Ambient operating temperature

4–55 °C (39–131 °F)

Ambient non-operating temperature

-40–70 °C (-40–158 °F)

Humidity

< 95% r.h. at 40 °C (104 °F)

Non-condensing

Operating altitude

Up to 3000 m (9842 ft)

Safety standards: IEC, EN, CSA, UL

Overvoltage category II, Pollution degree 2

For indoor use only

ISM Classification

ISM Group 1 Class B

According to CISPR 11

Operating principle

Thermostatted column compartment with dual, independent Peltier-element.

Solvent pre-heating and still-air operation for reduction of chromatographic band-broadening under UHPLC-conditions.

Designed for use with Agilent InfinityLab Assist

Intuitive User Interface, Automated Workflows, Predictive Maintenance & Assisted Troubleshooting

Temperature range

10 °C below ambient (minimum 4 °C) to 85 °C

^{All specifications are valid for distilled water at ambient temperature}

Temperature range increment

Settable in steps of 0.1 °C

^{All specifications are valid for distilled water at ambient temperature}

Temperature stability

± 0.1 °C

^{All specifications are valid for distilled water at ambient temperature}

Temperature accuracy

± 0.5 °C (with calibration at 40 °C)

^{All specifications are valid for distilled water at ambient temperature}

Temperature precision

0.05 °C

^{All specifications are valid for distilled water at ambient temperature}

Independent temperature zones

2  in single device

Column capacity

4  columns of up to 300 mm length plus InfinityLab Quick Connect fittings or pre-column.

The number of pre-column Quick Connect Heat Exchangers is scalable - each column can be equipped with an individual heat exchanger for best performance.

4-column selector valve is available to access each column without replumbing.

Heat-up/cool-down time

5 min from ambient to 40 °C

10 min from 40 °C to 20 °C

<25 min from 25 °C to 85 °C

^{All specifications are valid for distilled water at ambient temperature}

Solvent heat exchangers

Individually quick-installable for every column. Available at 3 µL internal volume, 0.17 mm i.d. capillary (large ID), 6 µL internal volume, 0.17 mm i.d. capillary (large ID high flow) and 9 µL internal volume, 0.17 mm i.d. capillary (bio-inert, metal-free).

Valve options

1 x integrated valve drive as option to host user-exchangeable Quick Change valve heads (up to 800 bar) of different formats:

2-position/6-port, 2-position/10-port, 4-column selection (4-position/10-port).

Also available in bio-inert materials.

Valve heads are automatically identified by their RFID tag.

Column identification

Optionally, column identification kit to track history of up to four columns.

Mounted on the left hand-side of module.

Instrument control

LC and CE Drivers A.02.14 or above.

Instrument Control Framework (ICF) A.02.04 or above

Lab Advisor B.02.08 or above

InfinityLab Assist (G7180A) with firmware D.07.40 or above

Agilent Instant Pilot (G4208A) B.02.20 or above.

For details about supported software versions refer to the compatibility matrix of your version of the LC & CE Drivers

Communication

Controller Area Network (CAN)

G7116A is a hosted module. (The LC stack needs to contain suitable host module or a LAN card for communication and control).

Maintenance and safety-related features

Extensive diagnostics, error detection and display (through Instant Pilot control module and Agilent Lab Advisor), leak detection, safe leak handling, leak output signal for shutdown of pumping system.

Low voltages in major maintenance areas.

GLP features

Valve heads carrying tags with serial number, pressure rating, number of switches and valve type.

Concept of column identification.

Housing

All materials recyclable.