Specification of the G7115A Diode Array Detector WR

Weight

12 kg (26.5 lbs)

Dimensions (height × width × depth)

140 x 396 x 436 mm (5.5 x 15.6 x 17.2 inches)

Line voltage

100–240 V~, ±10 %

Wide-ranging capability

Line frequency

50 or 60 Hz, ±5 %

Power consumption

110 VA, 100 W

Ambient operating temperature

4–55 °C (39–131 °F)

Ambient non-operating temperature

-40–70 °C (-40–158 °F)

Humidity

< 95 % r.h. at 40 °C (104 °F)

Non-condensing

Operating altitude

Up to 3000 m (9842 ft)

Safety standards: IEC, EN, CSA, UL

Overvoltage category II, Pollution degree 2

For indoor use only

ISM classification

ISM Group 1 Class B

According to CISPR 11

Detection type

1024-element photodiode array

Designed for use with Agilent InfinityLab Assist

Intuitive User Interface, Automated Workflows, Predictive Maintenance & Assisted Troubleshooting

Light source

Deuterium and tungsten lamps

Number of signals

8

Maximum data rate

120 Hz

Short term signal noise (ASTM)

< ± 0.7·10^-5 AU at 254 and 750 nm

Drift

< 0.9·10^-3 AU/h at 254 nm and 750 nm

Linear absorbance range

> 2 AU (5 %) at 273 nm

Wavelength range

190 – 950 nm

Wavelength accuracy

± 1 nm, self-calibration with deuterium lines, verification with holmium oxide filter

Wavelength bunching

1 – 400 nm, programmable in 1 nm steps

Slit width

1, 2, 4 , 8, 16 nm

Diode width

~ 1 nm

Time programmable

Wavelength, polarity, peak width, lamp bandwidth, auto balance, wavelength range, threshold, spectra storage mode

Flow cells

Standard: 13 µL volume, 10 mm cell path length and 120 bar (1740 psi) pressure maximum

Standard bio-inert: 13 µL volume, 10 mm cell path length and 120 bar (1740 psi) pressure maximum

Semi-micro: 5 µL volume, 6 mm cell path length and 120 bar (1740 psi) pressure maximum

Micro: 2 µL volume, 3 mm cell path length, 120 bar (1740 psi) pressure maximum

Semi-nano: 500 nL volume, 10 mm cell path length and 40 bar (580 psi) pressure maximum

Nano: 80 nL volume, 6 mm cell path length and 40 bar (580 psi) pressure maximum

High pressure: 1.7 µL volume, 6 mm cell path length and 400 bar (5800 psi) pressure maximum

Prep SST: 3 mm cell path length and 120 bar (1740 psi) pressure maximum

Prep Quartz: 3 mm cell path length and 50 bar (1740 psi) pressure maximum

Prep Quartz:0.3 mm cell path length and 50 bar (1740 psi) pressure maximum

Prep Quartz: 0.06 mm cell path length and 50 bar (1740 psi) pressure maximum

SFC Flow Cell: 13 μL volume, 10 mm cell path length and 400 bar (5800 psi) pressure maximum

SFC Flow Cell LD: 2 μL volume, 3 mm cell path length and 400 bar (5800 psi) pressure maximum

Spectral tools

Data analysis software for spectra evaluation, including spectral libraries and peak purity functions

Analog output

Recorder/integrator: 100 mV or 1 V, output range 0.001 – 2 AU, one output

Instrument control

LC and CE Drivers A.02.14 or above

Instrument Control Framework (ICF) A.02.04 or above

Lab Advisor B.02.08 or above

InfinityLab Assist (G7180A) with firmware D.07.40 or above

Agilent Instant Pilot (G4208A) with firmware B.02.20 or above

For details about supported software versions refer to the compatibility matrix of your version of the LC and CE Drivers.

Communication

LAN, Controller-Area Network (CAN), USB

Extended Remote Interface (ERI): ready, start, stop and shut-down signals

GLP

RFID for electronics records of flow cell and UV lamp conditions (path length, volume, product number, serial number, test passed, usage)

Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of lamp burn time with user-setable limits and feedback messages. Electronic records of maintenance and errors. Verification of wavelength accuracy with built-in holmium oxide filter.

Safety and maintenance

Extensive diagnostics, error detection and display through Agilent Instant Pilot and Agilent Lab Advisor software. Leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas.

Housing

All materials recyclable.

Others

Second generation of Electronic temperature control (ETC) for the complete optical unit