Specifications

Weight

11 kg (24.3 lbs)

Dimensions (height × width × depth)

140 x 396 x 436 mm (5.5 x 15.6 x 17.2 inches)

Line voltage

100–240 V~, ±10%

Wide-ranging capability

Line frequency

50 or 60 Hz, ±5%

Power consumption

80 VA, 70 W

Ambient operating temperature

4–55 °C (39–131 °F)

Ambient non-operating temperature

-40–70 °C (-40–158 °F)

Humidity

< 95% r.h. at 40 °C (104 °F)

Non-condensing

Operating altitude

Up to 3000 m (9842 ft)

Safety standards: IEC, EN, CSA, UL

Overvoltage category II, Pollution degree 2

For indoor use only

ISM classification

ISM Group 1 Class B

According to CISPR 11

Detection type

Double-beam photometer

Designed for use with Agilent InfinityLab Assist

Intuitive User Interface, Automated Workflows, Predictive Maintenance & Assisted Troubleshooting

Light source

Deuterium lamp

Number of signals

Single and dual wavelength detection

Maximum data rate

240 Hz (single wavelength detection)

2.5 Hz (dual wavelength detection)

Short term signal noise (ASTM)

< ± 0.15·10^-5 AU, at 230 nm (single wavelength detection)

< ± 0.80·10^-5 AU, at 230 nm and 254 nm (dual wavelength detection)

Drift

< 1·10^-4 AU/h, at 230 nm

Linear absorbance range

> 2.5 AU upper limit

Wavelength range

190 – 600 nm

Wavelength accuracy

± 1 nm, self-calibration with deuterium lines, verification with holmium oxide filter

Wavelength precision

< ± 0.1 nm

Slit width

6.5 nm typical over whole wavelength range

Time programmable

Wavelength, polarity, peak width, lamp on/off

Flow cells

Standard: 14 µL volume, 10 mm cell path length and 40 bar (580 psi) pressure maximum

Micro: 2 µL volume, 3 mm cell path length and 120 bar (1760 psi) pressure maximum

Semi-micro: 5 µL volume, 6 mm cell path length and 40 bar (580 psi) pressure maximum

Standard Bio: 14 µL volume, 10 mm cell path length and 40 bar (580 psi) pressure maximum

Micro Bio: 2 µL volume, 3 mm cell path length and 120 bar (1760 psi) pressure maximum

Preparative SST: 4 µL volume, 3 mm cell path length and 120 bar (1760 psi) pressure maximum

Preparative Quartz: 4 µL volume, 3 mm cell path length and 50 bar (725 psi) pressure maximum

Preparative Quartz: 0.3 mm cell path length and 50 bar (725 psi) pressure maximum

Preparative Quartz: 0.06 mm cell path length and 50 bar (725 psi) pressure maximum

High pressure: 14 µL volume, 10 mm cell path length and 400 bar (5800 psi) pressure maximum

Spectral tools

Stop-flow wavelength scan

Analog output

Recorder/Integrator 100 mV or 1 V, 1 output

Instrument Control

LC and CE Drivers A.02.11 or above

Instrument Control Framework (ICF) A.02.04 or above

Lab Advisor B.02.06 or above

InfinityLab Assist (G7180A) with firmware D.07.40 or above

Agilent Instant Pilot (G4208A) B.02.19 or above

For details about supported software versions refer to the compatibility matrix of your version of the LC and CE Drivers

Communication

LAN, Controller Area Network (CAN), USB

Extended Remote Interface: ready, start, stop and shut-down signals

GLP

Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of lamp burn time with user settable limits and feedback messages. Electronic records of maintenance and errors. RFID for electronics records of flow cell and UV lamp conditions (path length, volume, product number, serial number, test passed, and usage). Verification of wavelength accuracy with built-in holmium oxide filter.

Safety and maintenance

Extensive diagnostics, error detection and display through Agilent Instant Pilot and Agilent Lab Advisor software. Leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas. Tracking of flow cells and lamps with RFID (radio frequency identification) tags.

Housing

All materials recyclable.

Others

Second generation of Electronic temperature control (ETC) for the complete optical unit.