Specifications

Weight

17.8 kg (39.2 lbs)

Dimensions (height × width × depth)

180 × 396  × 436 mm (7.1  × 15.6  × 17.2 inches)

Line voltage

100 – 240 V~, ± 10 %

Wide-ranging capability

Line frequency

50  or 60 Hz, ± 5 %

Power consumption

90 VA, 74 W

Ambient operating temperature

4 – 55 °C (39 – 131 °F)

Ambient non-operating temperature

-40 – 70 °C (-40 – 158 °F)

Humidity

< 95 % r.h. at 40 °C (104 °F)

Non-condensing

Operating altitude

Up to 3000 m (9842 ft)

Safety standards: IEC, CSA, UL

Overvoltage category II, Pollution degree 2

For indoor use only

ISM Classification

ISM Group 1 Class B

According to CISPR 11

Hydraulic system

Two dual piston in series pumps with servo-controlled variable stroke drive, power transmission by gears and ball screws, floating pistons

Designed for use with Agilent InfinityLab Assist

Intuitive User Interface, Automated Workflows, Predictive Maintenance & Assisted Troubleshooting

Flow range

settable: 0.001 – 5 mL/min

recommended: 0.05 – 5.0 mL/min

Set points in 0.001 mL/min increments

Flow precision

≤ 0.07 % RSD or < 0.02 min SD, whichever is greater

Based on retention time at constant temperature

Flow accuracy

± 1 % or 10 µL/min, whichever is greater

Pumping degassed H₂O at 10 MPa (100 bar, 1450 psi)

Pressure operating range

Up to 60 MPa (600 bar, 8702 psi) up to 5 mL/min

Pressure pulsation

< 2 % amplitude (typically < 1.3 %), or < 0.3 MPa (3 bar, 44 psi), whichever is greater

Low delay volume configuration: < 5 % amplitude (typically < 2 %)

Compressibility compensation

Pre-defined, based on mobile phase compressibility

Recommended pH range

1.0 – 12.5 

Solvents with pH < 2.3  should not contain acids that attack stainless steel

Gradient formation

High-pressure binary mixing

Delay volume

Standard delay volume configuration: 600 – 900 µL, (includes 400 µL mixer), dependent on back pressure

Low delay volume configuration: 120 µL

Measured with water at 1 mL/min (water/water with tracer)

Composition range

Settable: 0 – 100 %

Recommended: 1 – 99 % or 5 µL/min per channel, whichever is greater

Composition precision

< 0.15 % RSD or < 0.04 min SD, whichever is greater

At 0.2  and 1 mL/min; based on retention time at constant temperature

Composition accuracy

± 0.35 % absolute

At 2 mL/min, at 10 MPa (100 bar, 1450 psi) (water/water with tracer)

Integrated degassing unit

Number of channels: 2

Internal volume per channel: 0.45 mL

Instrument control

LC & CE Drivers A.02.14 or above

Instrument Control Framework (ICF) A.02.04 or above

Lab Advisor software B.02.08 or above

InfinityLab Assist (G7180A) with firmware D.07.40 or above

Instant Pilot (G4208A) with firmware B.02.20 or above

For details about supported software versions refer to the compatibility matrix of your version of the LC and CE Drivers

Communication

Controller Area Network (CAN)

Local Area Network (LAN)

Extended Remote Interface (ERI)

Universal Serial Bus (USB)

Safety and maintenance

Extensive diagnostics, error detection and display through Agilent Lab Advisor, leak detection, safe leak handling, leak output signal for shutdown of the pumping system. Low voltage in major maintenance areas.

GLP features

Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of seal wear and volume of pumped mobile phase with pre-defined and user settable limits and feedback messages. Electronic records of maintenance and errors.

Housing

All materials are recyclable