Specifications

Weight

16.1 kg (35.5 lbs)

Dimensions (height × width × depth)

180 x 396 x 436 mm (7.1 x 15.6 x 17.2 inches)

Line voltage

100–240 V~, ±10%

Wide-ranging capability

Line frequency

50 or 60 Hz, ±5%

Power consumption

120 VA / 110 W

Ambient operating temperature

4–55 °C (39–131 °F)

Ambient non-operating temperature

-40–70 °C (-40–158 °F)

Humidity

< 95% r.h. at 40 °C (104 °F)

Non-condensing

Operating altitude

Up to 3000 m (9842 ft)

Safety standards: IEC, EN, CSA, UL

Overvoltage category II, Pollution degree 2

For indoor use only

ISM Classification

ISM Group 1 Class B

According to CISPR 11

Hydraulic system

Dual pistons in series pump with proprietary servo-controlled variable stroke design and smooth motion control for active damping.

Designed for use with Agilent InfinityLab Assist

Intuitive User Interface,
Automated Workflows,
Predictive Maintenance &
Assisted Troubleshooting

Pump resolution step size

300 pL

Flow range

Settable: 0.001 – 5 mL/min

In 0.001 mL/min increments

Flow precision

≤ 0.07 % RSD or 0.01 min SD, whichever is greater

Flow accuracy

± 1 % or ± 10 µL/min, whichever is greater

Pumping degassed H₂O

Pressure operating range

Up to 130 MPa (1300 bar, 18855 psi) up to 2 mL/min

Ramping down to 80 MPa (800 bar, 11603 psi) at 5 mL/min

Pressure pulsation

< 1 % amplitude or < 0.5 MPa (5 bar), whichever is greater

Compressibility compensation

Automatic

When using "Solvent Types" in method

Recommended pH-range

1.0 – 12.5 

Solvents with pH < 2.3  should not contain acids which attack stainless steel.

Gradient formation

Low pressure quaternary mixing/gradient capability using proprietary high-speed proportioning valve

Delay volume

≤ 350 µL (default configuration)

Measured with water at 1 mL/min (water/water with tracer)

Composition range

Settable: 0 – 100 %

Recommended: 1 – 99 %

Composition precision

< 0.15 % RSD or 0.02 min SD, whichever is greater

Composition accuracy

± 0.4 % absolute

At 1 mL/min for water/water with tracer

Number of solvents

4

Solvent selection valve

Internal 4-solvent gradient formation valve included.

External 2x 12 solvent valve as option, fully integrated in the pump control interface.

Integrated degassing unit

Number of channels: 4

Internal volume per channel: 1.5 mL

Materials in contact with solvent

TFE/PDD copolymer, PFA, PEEK, FEP, ETFE, Stainless Steel, Aluminum Oxide-based Ceramic, Ruby, Sapphire, Gold, Zirconium Oxide-based Ceramic, Tantalum, UHMW-PE, Polyimide, DLC Coated Stainless Steel

Automatic purge valve

Enables automatic software-embedded functionalities such as switching the optional mixer in and out or automatic purging.

Active Seal wash

Included

Intelligent System Emulation Technology (ISET)

Included

Instrument control

LC & CE Drivers A.02.11 or above

Instrument Control Framework (ICF) A.02.03 or above

Lab Advisor software B.02.06 or above

InfinityLab Assist (G7180A) with firmware D.07.40 or above

Instant Pilot (G4208A) with firmware B.02.17 or above

For details about supported software versions refer to the compatibility matrix of your version of the LC & CE Drivers.

Communication

Controller Area Network (CAN), LAN, RS232C, APG remote: ready, start, stop, and shutdown signals

Safety features and maintenance

Leak detection, safe leak handling, leak output signal for shutdown of the pumping system. No hazardous voltages in major maintenance areas. Extensive diagnostics, error detection and display with Agilent Lab Advisor software.

GLP features

Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of seal wear and volume of pumped mobile phase with pre-defined and user settable limits and feedback messages. Electronic records of maintenance and errors.

Housing

All materials are recyclable.

Performance specifications determined with standard configuration (4CGV).