Specifications of the G4767A SFC Multisampler

Weight

22 kg (48.5 lbs)

w/o sample thermostat

Dimensions

(height × width × depth)

320 x 396 x 468 mm

(12.6 x 15.6 x 18.4 inches)

Line voltage

100 – 240 V~, ±10%

Wide-ranging capability

Line frequency

50 or 60 Hz, ±5%

Power consumption

180 VA, 180 W

Ambient operating temperature

4–40 °C (39 – 104 °F)

Ambient non-operating temperature

-40–70 °C (-40 – 158 °F)

Humidity

< 95% r.h. at 40 °C (104 °F)^{SampleThermostatIncluded}

Non-condensing

Operating altitude

Up to 3000 m (9842 ft)

Safety standards: IEC, EN, CSA, UL

Overvoltage category II, Pollution degree 2

For indoor use only

ISM Classification

ISM Group 1 Class B

According to CISPR 11

Permitted solvents

Boiling point ≥ 56 °C (133 °F)

Auto-ignition temperature ≥ 200 °C (392 °F)

Designed for use with Agilent InfinityLab Assist

Intuitive User Interface, Automated Workflows, Predictive Maintenance & Assisted Troubleshooting

Injection range SFC Mode

Default 0.1–90 μL in 0.1 μL increments

Up to 600 bar using the 100 μL analytical head

Injection range HPLC/Hybrid Mode

Default 0.1–100 μL in 0.1 μL increments

Up to 800 bar using the 100 μL analytical head

Injection precision in LC mode

< 0.15% RSD or SD <10 nL, whatever is greater

Measured caffeine

Injection precision in SFC mode

0.1 – 10 μl: < 0.3% RSD or 10 nL, whatever is greater. At 10 μl: < 0.25% RSD

Measured caffeine

Injection linearity in SFC mode

0.9999 in the range of 0.1–10 μL

Measured caffeine

Injection linearity in LC mode

0.9999 in the range of 0.1–100 μL

Measured caffeine

SFC Pressure range

Up to 600 bar

Max. pressure for basic instrument (SFC Mode)

HPLC/Hybrid Pressure range

Up to 800 bar

Max. pressure for basic instrument (LC Mode)

Sample viscosity range

0.2–5 cP

Sample capacity

1H Drawer up to 8 drawers and 16 positions Shallow well plates (MTP)

Max. 6144/1536 samples (384 MTP/96)

2H Drawer up to 4 drawers and 8 positions MTP, deep well plates, vials, Eppendorf

3072 samples, 432 vials (2 mL)

3H Drawer up to 2 drawers and 4 positions MTP, deep well plates, vials up to 6 mL, Eppendorf

1536 samples, 60 vials (6 mL), 384 vials (1 mL), 216 vials (2 mL)

LC Injection cycle time

< 10 s using following standard conditions: Default draw speed: 100 μL/min Default eject speed: 400 μL/min Injection volume: 1 μL

Time between 2 injections is not mechanically limited, time delay depends on communication speed of software, OS or network connections

SFC Injection cycle time

< 13 s using following conditions: Default draw speed: 100 μL/min Feed Speed: 1000 μL/min Injection volume: 1 μL

With additional 4 s purge within run.

Carry over in LC mode

< 0.003% (30 ppm)

Based on injections using the standard LC injection principle

Carry over in SFC mode

< 0.002% (20 ppm)

Based on injections using the Feed Injection principle

Instrument Control

LC & CE Drivers A.02.16 or above

Instrument Control Framework (ICF) A.02.04 or above

Instant Pilot (G4208A) with firmware B.02.21 or above

Lab Advisor B.02.09 or above

InfinityLab Assist (G7180A) with firmware D.07.40 or above

For details about supported software versions refer to the compatibility matrix of your version of the LC & CE Drivers

Communications

Controller Area Network (CAN)

Local Area Network (LAN)

ERI: ready, start, stop and shut-down signals

Maintenance and safety-related features

Extensive diagnostics, error detection and display with Agilent Lab Advisor software

Leak detection, safe leak handling, leak output signal for shutdown of pumping system, and low voltages in major maintenance areas

GLP features

Early maintenance feedback (EMF) for continuous tracking of instrument usage with user-settable limits and feedback messages. Electronic records of maintenance and errors

Housing

All materials recyclable.